Search found 2698 matches
- Fri Apr 19, 2024 10:37 am
- Forum: Technical Discussion
- Topic: Taming amp gain in single channel deluxe reverb build
- Replies: 41
- Views: 756
Re: Taming amp gain in single channel deluxe reverb build
... So the 47k would then be a voltage divider with the plate resistance(tube and resistor)? That's exactly it! The Thevenin equivalent circuit for the triode stage is a voltage source (zero impedance) in series with about a 40k resistance (anode load resistor // valve's internal anode resistance)....
- Fri Apr 19, 2024 10:31 am
- Forum: Marshall Discussion
- Topic: Bad case of ghosting...I've tried everything.
- Replies: 5
- Views: 147
Re: Bad case of ghosting...I've tried everything.
I suggest cleaning up all connections to the chassis. One or more of those lugs etc may have developed corrosion etc, preventing a good connection.
- Thu Apr 18, 2024 5:19 pm
- Forum: Technical Discussion
- Topic: Taming amp gain in single channel deluxe reverb build
- Replies: 41
- Views: 756
Re: Taming amp gain in single channel deluxe reverb build
... I biased the 6V6 to around 415V and 20mA, so basically 20mV of current ... TP 37 and 38 206V AC TP39 11.4 So your HT voltage is higher than the Fender schematic you're referencing. I guess the Z HT node voltage will be higher too. More voltage on the screen grids means a higher stage gain for t...
- Thu Apr 18, 2024 8:55 am
- Forum: Technical Discussion
- Topic: Taming amp gain in single channel deluxe reverb build
- Replies: 41
- Views: 756
Re: Taming amp gain in single channel deluxe reverb build
I just finished the initial build of a single channel deluxe reverb, sans tremolo. I'm using a classictone 40-18019 PT and the OT from a Hammond AO35. The hammond has 2 EL84's into an 8r load. I figured the 6V6 would be relatively close. ... There seems to be some confusion as to whether you've use...
- Fri Apr 05, 2024 2:52 pm
- Forum: Dumble Discussion
- Topic: ODS Inspired Build; #102 Values with Buffered FX Loop
- Replies: 20
- Views: 709
Re: ODS Inspired Build; #102 Values with Buffered FX Loop
Same as an HT winding where the CT is grounded, the voltages at the opposite ends of the coil are out of phase. The one that is out of phase with the secondary shows a higher voltage because its sine wave is high when the one at the secondary hot is low. Ahh, the voltmeters are with respect to the ...
- Fri Apr 05, 2024 12:17 am
- Forum: Dumble Discussion
- Topic: ODS Inspired Build; #102 Values with Buffered FX Loop
- Replies: 20
- Views: 709
Re: ODS Inspired Build; #102 Values with Buffered FX Loop
My thinking is both voltages should be the same, any idea what the mechanism is that causes them to differ like that?
- Thu Apr 04, 2024 10:17 am
- Forum: Technical Discussion
- Topic: Deluxe Reverb Build
- Replies: 20
- Views: 516
- Wed Apr 03, 2024 1:20 pm
- Forum: Fender Discussion
- Topic: Deluxe Reverb power transformer change?
- Replies: 16
- Views: 1077
Re: Deluxe Reverb power transformer change?
Derek at Watford Valves advises that the Philips ECG WGB run fine in pretty much any guitar amp, even the crazy high voltage late 70s Fenders.
And a mere £50 each!
He better puts his prices up before they migrate back across the pond
https://watfordvalves.com/product_detail.asp?id=1313
And a mere £50 each!
He better puts his prices up before they migrate back across the pond
https://watfordvalves.com/product_detail.asp?id=1313
- Mon Apr 01, 2024 5:32 pm
- Forum: Technical Discussion
- Topic: Lead Dress for Star Grounding
- Replies: 5
- Views: 206
Re: Lead Dress for Star Grounding
... The PT centertap wire to the negative of the first filter cap has big and pulsed (containing higher harmonics) currents running on it. Run that one short and direct, and don't cluster it up with anything else. ... Just to confirm and clarify, the CT of the high voltage winding should be directl...
- Mon Apr 01, 2024 10:28 am
- Forum: Technical Discussion
- Topic: Blackvibe 6L6 Strange behavior on tone pots
- Replies: 14
- Views: 393
Re: Blackvibe 6L6 Strange behavior on tone pots
... On any blackpanel amp if you turn all the tone pots to 0 ... Fender knobs for these amps are 1-10, no 0 available, CCW = 1, CW = 10. ... 6k8 resistance to ground, like a 10kA mid pot set at ~3:00. With a regular 1-10 knob and 10k log pot, I recall a fairly high setting is required, maybe around...
- Sun Mar 24, 2024 12:29 am
- Forum: Technical Discussion
- Topic: Heater Wire Ground
- Replies: 30
- Views: 518
Re: Heater Wire Ground
(1) And the heater center taps are sometimes not too accurate. A couple of resistors may well make a better center tap, with lower induced hum. Why do you think that the minimum hum is on the middle of very- too much precision- resistors ? Give us some technical reference and measurement. 8) I've n...
- Sat Mar 23, 2024 1:15 pm
- Forum: Technical Discussion
- Topic: Bias range question.
- Replies: 27
- Views: 621
Re: Bias range question.
You should start with the bias voltage at the most negative setting (largest number). Talking about negative voltage is always confusing. The convention I follow is more negative is lower, which is mathematically correct and follows the convention for temperature. I still write it two ways to make ...
- Thu Mar 21, 2024 11:57 pm
- Forum: Fender Discussion
- Topic: Can I use a Bassman 70watts PT and OT for a Deluxe reverb?
- Replies: 11
- Views: 390
Re: Can I use a Bassman 70watts PT and OT for a Deluxe reverb?
Yes, all the silverface 70 and 135 watt amps where Ul and as such not what you want it your looking for a true Deluxe playing feel and response . To describe those OTs / output stages as UL implies that their design has been optimised for linearity. As the taps are at about 12.5%, my understanding ...
- Thu Mar 21, 2024 7:03 pm
- Forum: Speakers and Cabinets
- Topic: Cabinet made of OSB instead of pine
- Replies: 13
- Views: 486
- Thu Mar 21, 2024 3:02 pm
- Forum: Fender Discussion
- Topic: Can I use a Bassman 70watts PT and OT for a Deluxe reverb?
- Replies: 11
- Views: 390
Re: Can I use a Bassman 70watts PT and OT for a Deluxe reverb?
Not from those transformer codes, they match this earlier version https://el34world.com/charts/Schematics ... man_10.pdf
Still super high HT voltage though.
I seem to recall that the OT there is surprisingly wimpy.