O.K. Instructions said take reading from pin 8 (low) to pin 3 (high). That is what I did. Smoke. Should have taken pin 8 to ground?
Maybe this helps.
Search found 28 matches
- Sat Jul 26, 2008 10:03 pm
- Forum: Trainwreck Discussion
- Topic: Express Dead
- Replies: 4
- Views: 1109
- Sat Jul 26, 2008 8:34 pm
- Forum: Trainwreck Discussion
- Topic: Express Dead
- Replies: 4
- Views: 1109
Express Dead
OK.....I bought a Biastool. Instructions required a reading for cathode to plate voltage. I had the tubes in while taking this reading. Smoke started rising from the socket (filament wire maybe). Tube was not glowing anymore. The second power tube was glowing. Turned it off (obviously). Removed the ...
- Fri Dec 29, 2006 3:32 pm
- Forum: Trainwreck Discussion
- Topic: anyone have a Bill of materials for any of the wrecks?
- Replies: 5
- Views: 1463
Re: anyone have a Bill of materials for any of the wrecks?
I wouldn't consider all these components "High" quality. There are a multitude of options to upgrade your build. For example....I used Vishay Dale resistors + or - 1%. Sozo tone caps. Switchcraft input, output jacks. Whatever you fancy. It's all in this forum. Just search. This is a good list to use...
- Thu Nov 09, 2006 10:43 pm
- Forum: Trainwreck Discussion
- Topic: Irene was born today
- Replies: 9
- Views: 2218
A few pictures.
Here she is. I've tweaked a bit. Overall, an awesome amp. My bright switch was noisy. I clipped it off and used the 100 pf cap for now. That is bright enough for me. I'll put a better switch in its place. I want to replace the tube sockets also. They squeal if they touch the metal base sides. Cheap ...
- Tue Oct 31, 2006 1:29 pm
- Forum: Trainwreck Discussion
- Topic: Irene was born today
- Replies: 9
- Views: 2218
Re: Irene was born today
Humbucker, The Trim Pot was the 25K bias adjustment on the power board. My Tubes must have been under biased causing buzzzzz. To reduce Hisssss, you can change to lower gain pre amp tubes. 12AU7's virtually eliminate the hiss, but lower gain. Great for clean tone. The Tubestore has a chart that show...
- Tue Oct 31, 2006 1:08 am
- Forum: Trainwreck Discussion
- Topic: Irene was born today
- Replies: 9
- Views: 2218
Re: Irene was born today
I was correct in thinking the trim pot would fix the buzzziness to certain loud notes and chords. I put the trim pot in (after waiting a month to receive it from Mouser) and the buzzzz is gone. Just great sustaining tone. Still has hiss. But, that's what ya get. I'm a happy camper. Now, How to prope...
- Mon Oct 30, 2006 4:02 am
- Forum: Trainwreck Discussion
- Topic: Irene was born today
- Replies: 9
- Views: 2218
Irene was born today
Thanks to all the information on this forum, I've built my first tube amp. I'm naming her Irene. My wifes name. At first there was no volume. I could tap on the chassis and heard it loud and clear. The amp was working, but not through the input jack. I checked all the voltages. They were good. I the...
- Mon Oct 23, 2006 3:36 am
- Forum: Trainwreck Discussion
- Topic: Fuse wiring
- Replies: 4
- Views: 896
Re: Fuse wiring
Thanks guys...I see Francesca has black wire (I assume hot) to the fuse. My power cord black wire is the hot. If you've done it that way.....I will too. Thanks again.
- Mon Oct 23, 2006 1:57 am
- Forum: Trainwreck Discussion
- Topic: Fuse wiring
- Replies: 4
- Views: 896
Fuse wiring
Basic question.....I've seen pictures of black wire or white wire from mains cord to fuse holder and then to power switch. Should common go to fuse holder, or hot? I want to get this one right before I wire it.
- Wed Oct 04, 2006 12:22 pm
- Forum: Trainwreck Discussion
- Topic: Supplier for 1K 25 watt cement resistor?
- Replies: 8
- Views: 1768
Re: Supplier for 1K 25 watt cement resistor?
Thank you Adjuster. That will work for me. Looks like a good site for supplies.
- Wed Oct 04, 2006 1:17 am
- Forum: Trainwreck Discussion
- Topic: Supplier for 1K 25 watt cement resistor?
- Replies: 8
- Views: 1768
Re: Supplier for 1K 25 watt cement resistor?
O.K. Is it O.K to use a 1k 10 watter instead? I know where to get those easily.
- Wed Oct 04, 2006 12:47 am
- Forum: Trainwreck Discussion
- Topic: Supplier for 1K 25 watt cement resistor?
- Replies: 8
- Views: 1768
Supplier for 1K 25 watt cement resistor?
I've got it on order from Mouser......no stock (you guys have them all!) They can't ship untill November!!!! You folks know of another good supplier? I've searched....www.cpcares.com has them. That's about it. My build will be slow. Maybe that's good? I only need about 3 more parts to start. For the...
- Thu Sep 28, 2006 10:03 pm
- Forum: Trainwreck Discussion
- Topic: Anyone else have a Nikspress on order?
- Replies: 10
- Views: 2108
I just ordered a chassis w/faceplate
I just ordered a chassis (my first "Express" build) and a faceplate from Nik. I'm in no hurry....I have 3 other amps to noodle with. I will have questions....hopefully only a few. This forum is packed with most of the answers already. I'll let you know when my parts arrive. I ordered some parts from...