Search found 4577 matches
- Fri May 03, 2024 10:20 am
- Forum: Technical Discussion
- Topic: JTM45 Build, looks alive but no sound,
- Replies: 4
- Views: 113
Re: JTM45 Build, looks alive but no sound,
This might help.
- Thu May 02, 2024 11:42 pm
- Forum: Technical Discussion
- Topic: Tubes For Mesa DC-3 Amp.......
- Replies: 2
- Views: 65
Re: Tubes For Mesa DC-3 Amp.......
And what in terms of your playing needs would as you say “ sound fabulous “?
- Thu May 02, 2024 10:06 am
- Forum: Technical Discussion
- Topic: Can I use 6v6's in a 69 Super Reverb ?
- Replies: 13
- Views: 296
Re: Can I use 6v6's in a 69 Super Reverb ?
If you start reducing the power supply voltage enough then what you like about the amps preamp section will be lost and at that point your truly better off to keep the amp as it is and open up your wallet to get a attenuator box on the output of the amp.
- Wed May 01, 2024 9:34 pm
- Forum: Technical Discussion
- Topic: Can I use 6v6's in a 69 Super Reverb ?
- Replies: 13
- Views: 296
Re: Can I use 6v6's in a 69 Super Reverb ?
The only time I used 6V6 outputs at that high a voltage was in a Highwatt 50, and they where JJ brand since they are stated to be good up to 500 volts, and after having them in the high watt I do not question that.
- Tue Apr 30, 2024 8:58 pm
- Forum: Technical Discussion
- Topic: Fender question
- Replies: 10
- Views: 264
Re: Fender question
All that has to be done is to remove a knob from the amp in question and compare.
This is front pot board and a chassis mounted pot for comparison.
This is front pot board and a chassis mounted pot for comparison.
- Tue Apr 30, 2024 10:12 am
- Forum: Technical Discussion
- Topic: What should I build?!?
- Replies: 7
- Views: 212
Re: What should I build?!?
Silvertone 1484 with KT66 outputs.
- Fri Apr 26, 2024 9:19 pm
- Forum: Technical Discussion
- Topic: Add an HT Fuse?
- Replies: 10
- Views: 350
Re: Add an HT Fuse?
Just to be 100% clear, my reasoning for what I posted is grounded in many decades of replacing power transformers in amps that have only a mains Fuse. In terms of a vintage amp that’s seen 40 plus years of use ( effects of heat accumulation) and the situation of repetitive blowing of the mains fuse ...
- Fri Apr 26, 2024 7:51 pm
- Forum: Technical Discussion
- Topic: Add an HT Fuse?
- Replies: 10
- Views: 350
Re: Add an HT Fuse?
A HT fuss will cover the whole DC side of the amp, but you mainly have filters that can go bad and output tubes. Filters will give you notice before they go south enough to pop the main fuse, but output tubes do not when they short . In light of this I would be more inclined to place in line with th...
- Fri Apr 26, 2024 10:19 am
- Forum: Technical Discussion
- Topic: Does anyone recognize this amp design?
- Replies: 10
- Views: 442
Re: Does anyone recognize this amp design?
The chassis I would say is not a one of since the nuts that will tie it up into the cabinet are tack welled in, so the amp started life as something else.
- Thu Apr 25, 2024 10:07 am
- Forum: Technical Discussion
- Topic: Blackvibe 6L6 Strange behavior on tone pots
- Replies: 17
- Views: 583
Re: Blackvibe 6L6 Strange behavior on tone pots
If your looking for any mid boost with aFender type tonestack the only way to get any of that or even get a flat response out of it is to turn the volume way up, crank full up the middle and set the bass and treble very low.
- Tue Apr 23, 2024 10:51 pm
- Forum: Technical Discussion
- Topic: Does anyone recognize this amp design?
- Replies: 10
- Views: 442
Re: Does anyone recognize this amp design?
Well it’s got very hard to find knobs from a Heathkit from what I can tell. It’s got a T03 cased transistor mounted near the fuses so I would have to assume it’s DC powered heaters. It looks like it’s got a old paper cased filter in there and 2 other filters that could be old and out of a Highwatt o...
- Sun Apr 21, 2024 12:07 pm
- Forum: Technical Discussion
- Topic: '63 Selmer Treble n bass dilemma..
- Replies: 4
- Views: 206
Re: '63 Selmer Treble n bass dilemma..
I have used the jtm45 PT in a 65 Fender Bassman and one would be hard pressed to hear the difference with the slightly lesser B+ voltage.
If you can surmount the mechanical difference I say go for it, and you would likely save the owner 100 bucks in the end also.
If you can surmount the mechanical difference I say go for it, and you would likely save the owner 100 bucks in the end also.
- Fri Apr 19, 2024 10:07 am
- Forum: Marshall Discussion
- Topic: Bad case of ghosting...I've tried everything.
- Replies: 5
- Views: 473
Re: Bad case of ghosting...I've tried everything.
You did not mention if you tried different known good preamp tubes.
I have had a condition like that a few times that was due to a preamp tube.
Have you tried a different speaker?
I have had a condition like that a few times that was due to a preamp tube.
Have you tried a different speaker?
- Fri Apr 19, 2024 10:01 am
- Forum: Technical Discussion
- Topic: Illinois brand capacitors still bad?
- Replies: 12
- Views: 498
Re: Illinois brand capacitors still bad?
Yes they are not at the bottom of the ladder any more.
- Wed Apr 17, 2024 7:02 pm
- Forum: Technical Discussion
- Topic: Taming amp gain in single channel deluxe reverb build
- Replies: 52
- Views: 1371
Re: Taming amp gain in single channel deluxe reverb build
Note that 6BQ5 PP output stage needs 10 volts less of grid to grid drive signal then a 6V6 output stage does.