Search found 39 matches
- Wed Nov 25, 2015 5:26 pm
- Forum: Technical Discussion
- Topic: Resistive Attenuators
- Replies: 7
- Views: 1305
Reactive Load instead...
Id go Reactive instead. Much more accurate representation of how a speaker reacts than just using a resistive load. Pete Thorn did a great comparison vid of a handful of popular resistive and reactive loads. Pretty clear differences even via youtube... Hope it helps! https://www.youtube.com/watch?v=...
- Sat Nov 14, 2015 10:17 pm
- Forum: Technical Discussion
- Topic: Rotary Switch recommendations
- Replies: 2
- Views: 543
- Fri Nov 13, 2015 4:44 pm
- Forum: Technical Discussion
- Topic: Rotary Switch recommendations
- Replies: 2
- Views: 543
Rotary Switch recommendations
Hello all,
Does anyone have recommendations on a 6 position rotary switch to switch between coupling caps ala Matchless etc? Would an Alpha type work?
Thank you!
-Michael
Does anyone have recommendations on a 6 position rotary switch to switch between coupling caps ala Matchless etc? Would an Alpha type work?
Thank you!
-Michael
- Fri Jan 16, 2015 3:20 pm
- Forum: Technical Discussion
- Topic: AX84 SEL with VVR Power amp only schematic check
- Replies: 10
- Views: 1709
Re: AX84 SEL with VVR Power amp only schematic check
Thanks Martin, That makes sense. I'll implement your design when my Mouser order arrives and see how it goes!
-Michael
-Michael
- Fri Jan 16, 2015 2:18 am
- Forum: Technical Discussion
- Topic: AX84 SEL with VVR Power amp only schematic check
- Replies: 10
- Views: 1709
Re: AX84 SEL with VVR Power amp only schematic check
Martin,
Do you have the VVR installed after R2 for a particular reason? it looks like our schematics are pretty similar (adding the dropping resistor into mine) except for that point. Thanks!
Do you have the VVR installed after R2 for a particular reason? it looks like our schematics are pretty similar (adding the dropping resistor into mine) except for that point. Thanks!
- Thu Jan 15, 2015 9:53 pm
- Forum: Technical Discussion
- Topic: AX84 SEL with VVR Power amp only schematic check
- Replies: 10
- Views: 1709
checking my math...
not yet. it will be before R2 after C1 as in my original schem. thinking outloud... maybe i'm off by a decimel... going off of voltages in the original SEL schematic i'd find the current across R3: (356-346)/1000 = .01A if i leave the VVR before R2 the V is 366 which is then sent to the preamp. So i...
- Thu Jan 15, 2015 8:10 pm
- Forum: Technical Discussion
- Topic: AX84 SEL with VVR Power amp only schematic check
- Replies: 10
- Views: 1709
Re: AX84 SEL with VVR Power amp only schematic check
Thanks guys. Looks like a 20k should do the trick.
- Thu Jan 15, 2015 2:09 am
- Forum: Technical Discussion
- Topic: AX84 SEL with VVR Power amp only schematic check
- Replies: 10
- Views: 1709
dropping resistor value
Thanks Colossal. That was an incredibly fast reply!
For my own knowledge, where did you come up with the 18-22kOhm resistor value for R3a? Thanks!
-Michael
For my own knowledge, where did you come up with the 18-22kOhm resistor value for R3a? Thanks!
-Michael
- Thu Jan 15, 2015 1:42 am
- Forum: Technical Discussion
- Topic: AX84 SEL with VVR Power amp only schematic check
- Replies: 10
- Views: 1709
AX84 SEL with VVR Power amp only schematic check
Hi Everyone, I've been lurking and learning for a while with this being my first post. I recently completed an Ax84 SEL build with the entire amp being scaled which has been working fine. I'd like to try scaling just the power amp. The original SEL schematics have the screens and part of the preamp ...