Thanks for all your help. I can't wait to get this wired and working
Search found 9 matches
- Wed Jul 19, 2017 9:24 pm
- Forum: Vox/Hiwatt Discussion
- Topic: Need help adding slave-in jack on Dr103 clone
- Replies: 15
- Views: 3407
Re: Need help adding slave-in jack on Dr103 clone
- Wed Jul 19, 2017 7:33 am
- Forum: Vox/Hiwatt Discussion
- Topic: Need help adding slave-in jack on Dr103 clone
- Replies: 15
- Views: 3407
Re: Need help adding slave-in jack on Dr103 clone
I like the Cliff jack a lot better. But I think we need to move the 22k to the other side to ground the disconnected end.
- Tue Jul 18, 2017 11:00 pm
- Forum: Vox/Hiwatt Discussion
- Topic: Need help adding slave-in jack on Dr103 clone
- Replies: 15
- Views: 3407
Re: Need help adding slave-in jack on Dr103 clone
Thanks for your help. I think this layout will disconnect the 22k and reconnect it to ground.
- Mon Jul 17, 2017 12:45 am
- Forum: Vox/Hiwatt Discussion
- Topic: Need help adding slave-in jack on Dr103 clone
- Replies: 15
- Views: 3407
Re: Need help adding slave-in jack on Dr103 clone
Just put in a send and return jacks/and or stero jack between the master volume pot wiper and phase inverter input. The cathode follower output before the PI would be the most logical place to put an effects loop send/return jacks. Thanks for the ideas. I think you guys are suggesting I bypass V3? ...
- Sun Jul 16, 2017 6:24 am
- Forum: Vox/Hiwatt Discussion
- Topic: Need help adding slave-in jack on Dr103 clone
- Replies: 15
- Views: 3407
Re: Need help adding slave-in jack on Dr103 clone
The slave input would have to go at the top of the master volume. I would put a 22n cap at the slave input jack, and use a switching contact to disconnect the 22k resistor feeding it. If you can arrange to ground the 22k, that would be even better. Are you suggesting the 22n be inline with the inco...
- Fri Jul 14, 2017 9:27 am
- Forum: Vox/Hiwatt Discussion
- Topic: Need help adding slave-in jack on Dr103 clone
- Replies: 15
- Views: 3407
Re: Need help adding slave-in jack on Dr103 clone
Take a look at the schematic for a Soundcity L/B 120 mk lV . Thanks for the suggestion. I looked it over and I don't think I can make that work. I'm not very knowledgeable on electronics so maybe I just don't understand. There is no master volume like I have on mine. There are 2 slave jacks. One ja...
- Wed Jul 12, 2017 11:45 pm
- Forum: Vox/Hiwatt Discussion
- Topic: Need help adding slave-in jack on Dr103 clone
- Replies: 15
- Views: 3407
Need help adding slave-in jack on Dr103 clone
I just finished building a DR103 clone using Mark Huss's diagrams and schematics (thanks Mark) and I'd like to add a slave-in jack. I'm looking to switch back and forth between the Hiwatt preamp and an outboard preamp. I can't find much info on this mod. From what I can gather I only need to add a j...
- Sun May 31, 2015 10:37 pm
- Forum: Technical Discussion
- Topic: Q about change in hum volume when biasing Hiwatt 100
- Replies: 5
- Views: 660
Re: Q about change in hum volume when biasing Hiwatt 100
Thanks a lot guys I appreciate it.
- Sun May 31, 2015 8:13 pm
- Forum: Technical Discussion
- Topic: Q about change in hum volume when biasing Hiwatt 100
- Replies: 5
- Views: 660
Q about change in hum volume when biasing Hiwatt 100
I had to add a voltage doubler to my 100 watt Hiwatt with el34s and discovered that while the 60hz hum diminishes as the left and right side bias voltages gets closer, it seems the amp is the quietest when there is a couple mv offset between the left and right sides. Should I ignore that or go with ...