The Amp Garage

amplifiednation wrote: ↑Fri Jun 16, 2023 10:13 am Looks great OP!

Thanks! And you would know, it’s one of your chassis! Thanks for selling those in this community.

EdG wrote: ↑Tue May 23, 2023 2:48 am Thanks so much for the info!!

You’re welcome!

What bothers me most is how to make such clean & precise cuts? Nice cab, by the way ... 8) Thanks! If you’re concerned about making clean precise cuts of aluminum trim, please know I didn’t use anything fancy. It was simply a hack saw with a bit of patience and extra care. I did a practice cut and ...

where can I find info on the Aluminum trim type, thickness and length? Is there a drawing somewhere? Screws etc.? Thank you! Furthermore, I didn’t actually find much or any information on the aluminum trim. I just winged it and I would say I nailed it. Use a common countersink in a drill to get the...

where can I find info on the Aluminum trim type, thickness and length? Is there a drawing somewhere? Screws etc.? Thank you! Sorry for the slow reply. I went to Home Depot, they sell aluminum there and they had 1/8” x 3/4” x 36” strips of it. Only a few dollars per unit. I just bought some screws t...

https://www.tubesandmore.com/products/transformer-power-117-v-primary-125-v-15-ma-secondary If you're not a stickler for voltages this transformer has 125v 15ma and 12v 0.3ma secondaries. If you trim the bobbin a little where the leads come over it fits inside a 1U rack. I've used it a few times an...

martin manning wrote: ↑Sat Apr 15, 2023 12:55 am See here: https://ampgarage.com/forum/viewtopic.p ... 73#p413673

You're amazing. Thanks!

I'm thinking about building a dumbleator. I'm having a hard time finding much information about transformers for this thing. From what I can gather in the pages on this forum specific to the Dumbleator is that the transformer is supposed to be 135V. I found these two transformers. I'm wondering if e...

Thanks a lot for that detailed response. I got the job done today. It looks great! My ODS #124 clone is officially finished. I'm so excited!

jabguit wrote: ↑Fri Feb 24, 2023 11:49 am attach to the cab

Thanks! Are there any tricks to ensure that the top horizontal aluminum bar aligns well with the vertical bars? Or do I just proceed with caution?

I’m in the final stages of a Dumble Style Cab build. I’m curious if there’s a specific way to mount the three pieces of aluminum trim pictured below. Do I affix them to the cabinet itself, or do I affix it to the grill cloth frame that goes in the middle. I know there are typically two holes towards...

martin manning wrote: ↑Mon Feb 20, 2023 1:24 pm Countersink first, and allow for the leather thickness. Leave the pilot holes until after the covering has been applied.

Thanks, Martin! I’ll do that.

I just realized this should be under “Speakers & Cabinets”… sorry everyone! I’m not sure the appropriate way to flag it for moderators to have it moved.

**MOVED per request**

Howdy y’all! Quick question. I’m wrapping a guitar cabinet in suede leather. I’m using these corners here… https://www.mojotone.com/Mojotone-Chrome-Fender-Style-2-Hole-Corners-w-Lip And these corners here… https://www.mojotone.com/Mojotone-Chrome-Fender-Style-3-Hole-Corners-No-Lip As you can see in ...

I recently built an ODS #124. I realized the transformer I originally ordered didn't have enough voltage (320V), so I ordered a new one (340V). My first transformer didn't have a center tap for the heater wires so I did what the ODS #124 schematic originally called for and I put in the 120 Ohm resis...