Search found 145 matches
- Fri Feb 17, 2023 7:36 pm
- Forum: Technical Discussion
- Topic: Dual rectifier tubes?
- Replies: 7
- Views: 577
Re: Dual rectifier tubes?
Tell me more about the PT having enough amps for a second 5y3 Not much to say. One 5Y3 needs 5V@2A. Plenty of PT choices available. Two 5Y3s need 5V@4A. Fewer choices and they are likely to be BIG and HEAVY. the two examples above seem to be wired differently in relation to the PT and each other. M...
- Fri Feb 17, 2023 5:45 pm
- Forum: Technical Discussion
- Topic: Dual rectifier tubes?
- Replies: 7
- Views: 577
Re: Dual rectifier tubes?
You are basically making the rectifier more efficient and handle more current. A single (larger) bottle would do the same thing basically. I suppose you could pull one for more sag, but I would worry about drawing too much through the one tube might be asking too much. Dual rectifiers is not about ...
- Fri Feb 17, 2023 4:43 pm
- Forum: Technical Discussion
- Topic: Dual rectifier tubes?
- Replies: 7
- Views: 577
Dual rectifier tubes?
I have a PP 6AQ5 amp that runs dual rectifier tubes, both 6x4. I love it, and have always been curios why there are two rectifiers. In this amp it looks like each 6x4 rectifier is fed by a different side of the PT, then the outputs are bridged. https://i.imgur.com/gAVeWnf.jpg There is also a paralle...
- Sun Jun 12, 2022 6:45 pm
- Forum: Garage Talk
- Topic: Bucking Transformer
- Replies: 11
- Views: 1734
Re: Bucking Transformer
I think Rob Robinette used a Hammond 166N12 for his bucking project. So maybe the Hammond 166N24?
I see you used a Radio Shack part for yours - I'm open to parts suggestions if there is a good readily available 24v T up to the task.
- Thu Jun 09, 2022 4:22 pm
- Forum: Garage Talk
- Topic: Bucking Transformer
- Replies: 11
- Views: 1734
Re: Bucking Transformer
I also need to figure out a bucking transformer, as I have 122v at my wall, and a 100v made in Japan tube amp that I want to use. I've seen some posts about making a bucking transformer to get down to 110v, but I need 100v. Ot is it better to just get a step-down transformer? I also have a couple 22...
- Fri Apr 22, 2022 9:23 pm
- Forum: Technical Discussion
- Topic: 60's projector amp - blowing fuses
- Replies: 37
- Views: 3016
- Fri Apr 22, 2022 5:36 pm
- Forum: Technical Discussion
- Topic: 60's projector amp - blowing fuses
- Replies: 37
- Views: 3016
Re: 60's projector amp - blowing fuses
I got the amp to stop blowing fuses by swapping the Power Transformer from another of the same amp. The original PT seemed to test fine, but under working conditions was problematic.
Now I'm working on biasing, and tweaking a few things, but it sounds great!
Now I'm working on biasing, and tweaking a few things, but it sounds great!
- Tue Apr 05, 2022 2:56 pm
- Forum: Technical Discussion
- Topic: 60's projector amp - blowing fuses
- Replies: 37
- Views: 3016
Re: 60's projector amp - blowing fuses
I think you may be subconsciously sabotaging yourself by labeling the amp's problem "the short". It is an overcurrent, and it might be caused by a short, but as I mentioned, I'm leaning to a problem with the output tubes losing their bias somehow. Maybe funny stuff on the shared cathode resistor, m...
- Mon Apr 04, 2022 2:57 pm
- Forum: Technical Discussion
- Topic: 60's projector amp - blowing fuses
- Replies: 37
- Views: 3016
Re: 60's projector amp - blowing fuses
Please don't add any new parts to the amp at this point unless they are being put in to replace confirmed bad parts! Resistors that have drifted in value even by 25% will not stop a circuit from working. It looks to meat this point that the issue it has now was caused by you possibly by replace a f...
- Mon Apr 04, 2022 3:45 am
- Forum: Technical Discussion
- Topic: 60's projector amp - blowing fuses
- Replies: 37
- Views: 3016
Re: 60's projector amp - blowing fuses
I've been reading the thread, trying to soak it up. I'm going to just say that I got from this, so correct me if I've missed something. > PT and OT resistance measurement seem normal. I think that "UL" reading may just be what your meter says on a complete open circuit. > PT and OT don't seem to ha...
- Fri Apr 01, 2022 5:40 pm
- Forum: Technical Discussion
- Topic: 60's projector amp - blowing fuses
- Replies: 37
- Views: 3016
Re: 60's projector amp - blowing fuses
I went through the turret board and removed every component. Everything tests with no shorts and the values were correct, albeit many had drifted 10-30% from original spec. I have then traced wires, and am checking everything for continuity to ground where it should or shouldn't be. Everything looks...
- Tue Mar 29, 2022 10:39 pm
- Forum: Technical Discussion
- Topic: 60's projector amp - blowing fuses
- Replies: 37
- Views: 3016
Re: 60's projector amp - blowing fuses
Please report back with your findings. I removed the C203 leg from R206, and both test to spec. I must have had a bad reading as they were in the circuit still. I soldered PT wires back on and did the additional tests. It is worth noting that the oscillator section of the circuit has been entirely ...
- Tue Mar 29, 2022 4:17 pm
- Forum: Technical Discussion
- Topic: 60's projector amp - blowing fuses
- Replies: 37
- Views: 3016
Re: 60's projector amp - blowing fuses
I am having a hard time understanding why r210 would have burnt up in the first place, but anyway what do you mean that you had R206 test bad? R206 could be shorted of left out of the circuit and a fuse would not blow, however if C203 was shorted, then that could be a issue. I don't know what happe...
- Tue Mar 29, 2022 3:27 pm
- Forum: Technical Discussion
- Topic: 60's projector amp - blowing fuses
- Replies: 37
- Views: 3016
Re: 60's projector amp - blowing fuses
Please report back with your findings. Thanks Stevem, I'll do that this evening and report back. I really appreciate you breaking it down into easy steps to try to track down the problem. On a related note of trying to trace things: This morning before work I started looking again at the schematic ...
- Tue Mar 29, 2022 1:05 am
- Forum: Technical Discussion
- Topic: 60's projector amp - blowing fuses
- Replies: 37
- Views: 3016
Re: 60's projector amp - blowing fuses
In addition to the PT voltages above, I tested my OT for resistance: http://www.geofex.com/ampdbug/outtrans.htm Primaries I get .84k ohms to each plate. And 2.5, 3.5 and 6.5 to ground for 3 primary wires. Secondaries: .2, .9, and 1.3 to ground. No continuity between primary and secondary. 16 ohm tap...