Just put 6L6's in my D'Lite
Moderators: pompeiisneaks, Colossal
Re: Just put 6L6's in my D'Lite
Stelligan, That was an amazing clip... Tone...Fingers Flying... very very nice.
Re: Just put 6L6's in my D'Lite
Thanks Raja. This amp building/tweaking is habit forming. The welcome side effect is all the extra playing is getting my chops back up!
Re: Just put 6L6's in my D'Lite
In regards to the relays, I used 5v relays off the 6.3v supply and they work fine. I can even put led's. Is there an advantage of going with 12v relays?
-
- Posts: 374
- Joined: Wed Nov 23, 2005 4:31 am
- Location: USA
Re: Just put 6L6's in my D'Lite
Very nice stelligan! What speaker, cab size were you using? Settings?
Re: Just put 6L6's in my D'Lite
Thanks Drumslinger. It was an emi RWB and the settings: Vol - 1:00 Treb - 2:00 Mid - 1:00 Bass - 2:30 Gain - 9:00 Level - 10:00 Master - 10:00 Pres - 2:00. Guitar volume was on 5 or 6. At the time this was recorded the impedance was mismatched. I had the switch on 8 ohms. After the switch to 6L6 the switch should have been on 16. It is louder with more clean headroom now. Sounds even better with impedance matched. Cab size is 24" wide, 10" deep pic below.
You do not have the required permissions to view the files attached to this post.
Re: Just put 6L6's in my D'Lite
Great looking amp!
Re: Just put 6L6's in my D'Lite
Very nice. That pretty well does it. 6L6 D'Lite it is. Stock D'Lite or what changes did you have to make to accomodate the 6L6s??
BTW, would love to hear more from you using that amp especially one where it's pushed hard.
Re: Just put 6L6's in my D'Lite
Thanks guys,
I really dig the amp. A few changes have been made since the clip was made. I'm running the impedance selector correctly now . Also have toyed with preamp tubes, noodled with plate resistors, and put in a G1265. Very nice now. And yes, the clip as posted is a stock D'Lite from BrownNote's kit with just a bias adjust for 6L6's. I am contemplating bigger iron because the clean headroom is not quite there for me at gig volumes. I'll try to post some gainer clips for coco soon.
I really dig the amp. A few changes have been made since the clip was made. I'm running the impedance selector correctly now . Also have toyed with preamp tubes, noodled with plate resistors, and put in a G1265. Very nice now. And yes, the clip as posted is a stock D'Lite from BrownNote's kit with just a bias adjust for 6L6's. I am contemplating bigger iron because the clean headroom is not quite there for me at gig volumes. I'll try to post some gainer clips for coco soon.
Re: Just put 6L6's in my D'Lite
Hey S,
Thanks for sharing your D'lite experience with us. VERY nice sounding amp and playing!!
A quick question (or two!): Do you recall the setting of your OD entrance pot and/or where you are running it at the moment?
How long have you been running the G1265 and have you observed any changes in tone/operation that might indicate any type of "break-in" period? I just put mine in and would re-think any mods to improve my OD tone if I knew that it would change significantly due to break in.
TIA,
Dave O.
Thanks for sharing your D'lite experience with us. VERY nice sounding amp and playing!!
A quick question (or two!): Do you recall the setting of your OD entrance pot and/or where you are running it at the moment?
How long have you been running the G1265 and have you observed any changes in tone/operation that might indicate any type of "break-in" period? I just put mine in and would re-think any mods to improve my OD tone if I knew that it would change significantly due to break in.
TIA,
Dave O.
Re: Just put 6L6's in my D'Lite
Thanks ampgeek,
OD trimmer at time of clip was at 10:30. Since then gurus from the ether have suggested noon. I am at noon now and it's still all good. I struggle with pushing the input too hard sometimes. I play may guitar at standard pitch with 12's on high E and a plain 20 for a G string. I like the tone of the clean channel when my guitar is rolled way back. I have been experimenting with light gauge strings and really like the way the amp responds but, I just can't get used to them slinky strings. The G1265 has nice crisp(not crispy) top end that seems to be mellowing just a bit - which is fine. Still not many hours on it so, can't help much there. It doesn't seem to be changing much over time to my ears. I was running the G1265 and an EV12L in an extension cab the other day. DANG. I just can't bring myself to haul that much to the gig. Very much thinking about a diagonal 2 X 12 open back combo configuration with some casters. The tweaks go on, and on..........
OD trimmer at time of clip was at 10:30. Since then gurus from the ether have suggested noon. I am at noon now and it's still all good. I struggle with pushing the input too hard sometimes. I play may guitar at standard pitch with 12's on high E and a plain 20 for a G string. I like the tone of the clean channel when my guitar is rolled way back. I have been experimenting with light gauge strings and really like the way the amp responds but, I just can't get used to them slinky strings. The G1265 has nice crisp(not crispy) top end that seems to be mellowing just a bit - which is fine. Still not many hours on it so, can't help much there. It doesn't seem to be changing much over time to my ears. I was running the G1265 and an EV12L in an extension cab the other day. DANG. I just can't bring myself to haul that much to the gig. Very much thinking about a diagonal 2 X 12 open back combo configuration with some casters. The tweaks go on, and on..........
Re: Just put 6L6's in my D'Lite
If I understood right, you're still using the 6V6 OT & PT in the amp, you only have swapped 6L6's in and biased?stelligan wrote:And yes, the clip as posted is a stock D'Lite from BrownNote's kit with just a bias adjust for 6L6's.
And you don't have any heat issues with the (for 6V6's designed) PT, since the 6L6's are drawing twice the heater current of a 6V6 ?
I'm also already very curious to these clips!stelligan wrote:I'll try to post some gainer clips for coco soon.
BTW: Awesome sound and playing Can't stop to listen to it!
My congrats!
Larry
Larry's Website now with included Pix's Gallery
Re: Just put 6L6's in my D'Lite
Thanks Larry,
the BrownNote iron is designed to accommodate 6V6, 6L6, and even EL34 - PT also has taps that can be doubled to supply relay power . The EL34s may be a bit of a stretch as current draw would be higher, but go to brownnote.net and search the forums for someone that may have a build using them. And yes, I have switched several times between 6V6 and 6L6. I'm remaining with 6L6 from now on as I prefer a little more muscular clean tone before breakup. A recent dry gainy clip of the amp is found here: http://ampgarage.com/forum/viewtopic.php?t=3142
IMO the D'Lite gets after a RF tone a bit more with 6L6s and does the lower gain LC thing a bit better with 6V6s. For an example of Carltonesque tones check here for a great sound from a killer player: http://www.brownnote.net/forum/viewtopi ... 55&start=0
the BrownNote iron is designed to accommodate 6V6, 6L6, and even EL34 - PT also has taps that can be doubled to supply relay power . The EL34s may be a bit of a stretch as current draw would be higher, but go to brownnote.net and search the forums for someone that may have a build using them. And yes, I have switched several times between 6V6 and 6L6. I'm remaining with 6L6 from now on as I prefer a little more muscular clean tone before breakup. A recent dry gainy clip of the amp is found here: http://ampgarage.com/forum/viewtopic.php?t=3142
IMO the D'Lite gets after a RF tone a bit more with 6L6s and does the lower gain LC thing a bit better with 6V6s. For an example of Carltonesque tones check here for a great sound from a killer player: http://www.brownnote.net/forum/viewtopi ... 55&start=0
- skyboltone
- Posts: 2287
- Joined: Wed May 10, 2006 7:02 pm
- Location: Sparks, NV, where nowhere looks like home.
Re: Just put 6L6's in my D'Lite
Ok, so what did you use for nice flexible 5 conductor cable?mlp-mx6 wrote:Well, I'll stick my neck out. Here's what I have done.
I found 12V LEDs at Radio Shack that have a built-in resistor. (They're nearly flat to the surface also, which I consider a plus for a footswitch application.) All I had to do was provide 12V across the LED wires with the proper polarity.
I use a 5-pin XLR to connect the amp to the footswitch. The 5 wires are -
+12V
Ground
OD Relay
PAB Relay
Mid boost relay
I use a DPDT for each of the 3 switches. One side switches the relays to ground. The other switches the +12V to the positive side of the LEDs.
3 switches, 3 different color LEDs. Works great.
The Last of the World's Great Human Beings
Seek immediate medical attention if you suddenly go either deaf or blind.
If you put the Federal Government in charge of the Sahara Desert, in five years time there would be a shortage of sand.
Seek immediate medical attention if you suddenly go either deaf or blind.
If you put the Federal Government in charge of the Sahara Desert, in five years time there would be a shortage of sand.
Re: Just put 6L6's in my D'Lite
How does the OT iron hold together [sound wise] with the 6L6s.stelligan wrote: ... the BrownNote iron is designed to accommodate 6V6, 6L6, and even EL34...