KMD 100W XV100SD Schematic
Moderators: pompeiisneaks, Colossal
- smokin' tone
- Posts: 89
- Joined: Wed Jun 14, 2006 6:07 pm
KMD 100W XV100SD Schematic
Does anybody have a schematic for this amp. I had one dropped off here the other night and so far I only got around to pulling out the chassis. Complaints are second gain channel not working and weak reverb. Figured the schem might come in handy for troubleshooting the SS portion of the preamp.
-
- Posts: 4576
- Joined: Fri Jan 24, 2014 3:01 pm
- Location: 1/3rd the way out one of the arms of the Milkyway.
Re: KMD 100W XV100SD Schematic
If the reverb section is SS and the amp uses a reverb pan than its very likely that the weak verb is due to the pan.
If the Amp is all tube in regards to both channels than it should be rather easy to just follow the signal thru until you loose it!
If the Amp is all tube in regards to both channels than it should be rather easy to just follow the signal thru until you loose it!
When I die, I want to go like my Grandfather did, peacefully in his sleep.
Not screaming like the passengers in his car!
Cutting out a man's tongue does not mean he’s a liar, but it does show that you fear the truth he might speak about you!
Not screaming like the passengers in his car!
Cutting out a man's tongue does not mean he’s a liar, but it does show that you fear the truth he might speak about you!
- smokin' tone
- Posts: 89
- Joined: Wed Jun 14, 2006 6:07 pm
Re: KMD 100W XV100SD Schematic
Tube reverb and the second gain channel is hybrid. I've been working late all week, gonna try to get back into it later today. Thanks.
Re: KMD 100W XV100SD Schematic
Here's the schematic. I have one of these amps, I'm in the process of converting it to a SSS type amp. Good luck on your repair. Let me know if you need any parts from my preamp board...I'll not be using it!
Mark
Mark
You do not have the required permissions to view the files attached to this post.
"- Yeah, can we have everything louder than everything else? Right!"- Ian Gillan
- smokin' tone
- Posts: 89
- Joined: Wed Jun 14, 2006 6:07 pm
Re: KMD 100W XV100SD Schematic
Wow, Thanks Mark. I was beginning to think this one was next to impossible to find. I'm going to jump back into it tomorrow, hopefully it won't be too tough. I appreciate the parts offer as well. I owe you one! Good call on your SSS conversion. There's some huge iron in these beast's.
-Steve
-Steve
Re: KMD 100W XV100SD Schematic
No problem Steve, glad I could help.
Mark
Mark
"- Yeah, can we have everything louder than everything else? Right!"- Ian Gillan
-
- Posts: 4576
- Joined: Fri Jan 24, 2014 3:01 pm
- Location: 1/3rd the way out one of the arms of the Milkyway.
Re: KMD 100W XV100SD Schematic
Take a look at the power supply's 16 volt power rails and confirm good levels for both the negative and positive voltage, these supply's at times fail one of the Zener diodes and or a bad filter , also that first tl072 IC chip may be shorted and loading down the supply!
When I die, I want to go like my Grandfather did, peacefully in his sleep.
Not screaming like the passengers in his car!
Cutting out a man's tongue does not mean he’s a liar, but it does show that you fear the truth he might speak about you!
Not screaming like the passengers in his car!
Cutting out a man's tongue does not mean he’s a liar, but it does show that you fear the truth he might speak about you!
- smokin' tone
- Posts: 89
- Joined: Wed Jun 14, 2006 6:07 pm
Re: KMD 100W XV100SD Schematic
Good suggestions-thanks Steve. I did check them and they were okay. I got the gain channel working. I checked the signal flow with my scope, turns out that V2B had a bad solder connection on pin 1 and the 470k resistor was open. Glad it was that easy, I was almost certain it was going to be an issue in the SS section.