ODS Eyelet Boards
Moderators: pompeiisneaks, Colossal
- martin manning
- Posts: 13323
- Joined: Sun Jul 06, 2008 12:43 am
- Location: 39°06' N 84°30' W
9 others liked this
ODS Eyelet Boards
In the .pdf's below are all-eyelet versions of the ODS PCB's and preamp eyelet board TAG member JBorders had made up for sale. The dimensions and mounting centers of those boards has become the "TAG standard" to which other members have had chassis fabricated for sale. They did not match any original Dumble ODS, and there were differences with respect to the (authentic) layout drawings posted on TAG by Tony Albany.
The original intent of the eyelet board drawings posted here was to enable a DIY replacement for the PCB and Preamp board set with the same overall dimensions and mounting centers. The preamp board closely matches Dumble's ODS component layout, so any important interactions will be preserved. The most notable differences are that all of the high voltage power supply filters are located on the main filter board, so the remotely mounted B+4 and B+5 filter capacitors seen in some layout drawings are not needed, and the bias supply circuit has two filters, as seen in later SN amps. Refer to the #183 layout drawing the for details of the B+ connections to the preamp board and the bias trimmer pot. The FET board layout required some rework for eyelet construction within the same dimensions as the PCB, but it has been proven to work well.
These eyelet boards can be configured for any ODS variant, including HRM and Bluesmaster using the small HRM EQ board. Note that OD and PAB relay connections for all variants are shown for OD "on" when the OD relay coil is energized. Some original amps were configured in the opposite way.
The original intent of the eyelet board drawings posted here was to enable a DIY replacement for the PCB and Preamp board set with the same overall dimensions and mounting centers. The preamp board closely matches Dumble's ODS component layout, so any important interactions will be preserved. The most notable differences are that all of the high voltage power supply filters are located on the main filter board, so the remotely mounted B+4 and B+5 filter capacitors seen in some layout drawings are not needed, and the bias supply circuit has two filters, as seen in later SN amps. Refer to the #183 layout drawing the for details of the B+ connections to the preamp board and the bias trimmer pot. The FET board layout required some rework for eyelet construction within the same dimensions as the PCB, but it has been proven to work well.
These eyelet boards can be configured for any ODS variant, including HRM and Bluesmaster using the small HRM EQ board. Note that OD and PAB relay connections for all variants are shown for OD "on" when the OD relay coil is energized. Some original amps were configured in the opposite way.
You do not have the required permissions to view the files attached to this post.
Last edited by martin manning on Mon May 13, 2024 9:20 pm, edited 32 times in total.
- dorrisant
- Posts: 2635
- Joined: Tue Sep 21, 2010 1:27 pm
- Location: Somewhere between a river and a cornfield
- Contact:
Re: ODS Eyelet Boards
Yes... Very nice. Thank you Martin.
"Education is what you're left with after you have forgotten what you have learned" - Enzo
Re: ODS Eyelet Boards
Nice work Martin, thank you.
Re: ODS Eyelet Boards
Thank you Martin.
- martin manning
- Posts: 13323
- Joined: Sun Jul 06, 2008 12:43 am
- Location: 39°06' N 84°30' W
Re: ODS Eyelet Boards
No trouble at all. A universal relay board has been added.
-
- Posts: 1377
- Joined: Wed Jun 11, 2008 6:56 pm
- Location: Arizona Desert
Re: ODS Eyelet Boards
Thanks Martin
D
D
Re: ODS Eyelet Boards
Perfect timing. Thanks
Re: ODS Eyelet Boards
Thank you very much for sharing the board layouts.
- martin manning
- Posts: 13323
- Joined: Sun Jul 06, 2008 12:43 am
- Location: 39°06' N 84°30' W
Re: ODS Eyelet Boards
Updated with relay connections for Skyliner OD/PAB, and corrected relay diode orientation. :^)
Re: ODS Eyelet Boards
You do not have the required permissions to view the files attached to this post.
Last edited by alkuz1961 on Wed Jan 08, 2020 8:16 am, edited 1 time in total.
-
- Posts: 1377
- Joined: Wed Jun 11, 2008 6:56 pm
- Location: Arizona Desert
Re: ODS Eyelet Boards
Nicely done!
Thank you!
D
Thank you!
D
Re: ODS Eyelet Boards
Thanks to all for sharing the eylet boards and the PCB-Layouts.
-
- Posts: 2070
- Joined: Sun Dec 26, 2010 6:19 pm
- Location: Boston
- Contact:
Re: ODS Eyelet Boards
Martin. Thank you for sharing this. The drawings are great.
Amplified Nation
www.amplifiednation.com
@ampnation
www.amplifiednation.com
@ampnation
-
- Posts: 2070
- Joined: Sun Dec 26, 2010 6:19 pm
- Location: Boston
- Contact:
Re: ODS Eyelet Boards
I draw up the eyelet boards in CAD. If anyone wants a set, let me know I'll get some made.
Amplified Nation
www.amplifiednation.com
@ampnation
www.amplifiednation.com
@ampnation