Search found 193 matches
- Wed Feb 09, 2011 6:11 pm
- Forum: Technical Discussion
- Topic: Any Problem with using Mains AC on the Heaters?
- Replies: 5
- Views: 1911
Re: Any Problem with using Mains AC on the Heaters?
Just remember you are tying your mains return to one side of the filament string. You are safest to keep it isolated from chassis and B+, but this may not be the best from an ac related hum standpoint.
- Wed Feb 09, 2011 3:56 pm
- Forum: Technical Discussion
- Topic: Developing the DIY "Champ" for first time builders
- Replies: 469
- Views: 101351
Re: Developing the DIY "Champ" for first time builders
I have this newer Bronco schematic that has voltages, can't be a whole lot of differences. Man! Those voltages have to be wrong. 24V at the cathode over470 Ohms is 51mA bias. 342 V on the plate with 51mA bias is 17W dissipation! Also, there appears to be 78V across the OPT primary, at 51mA that's 4...
- Tue Feb 08, 2011 10:54 pm
- Forum: Technical Discussion
- Topic: Developing the DIY "Champ" for first time builders
- Replies: 469
- Views: 101351
Re: Developing the DIY "Champ" for first time builders
The opt sounds like the GXSE10-8-5K but upright instead of low profile. If so, you could flip the drawing to be vertical and it should work. http://www.edcorusa.com/DWG/15000-EI087-100-HX.pdf I'm curious about the PT as I've been using one with the slightly lower ratings (50 vs 60mA) w/0 the 5V wind...
- Tue Feb 08, 2011 1:11 am
- Forum: Trainwreck Discussion
- Topic: Russian TrainWreck - Expresso Lite(Liverpool), Soviet tubes
- Replies: 56
- Views: 18992
Re: Russian TrainWreck - Expresso Lite(Liverpool), Soviet tubes
Thanks, the speaker panel and grill cloth were re-purposed from a Magnavox Console Stereo.
I've got one more left with the 12" speaker in it that I might use with my 5F1 inspired amp.
I've got one more left with the 12" speaker in it that I might use with my 5F1 inspired amp.
- Mon Feb 07, 2011 11:29 pm
- Forum: Technical Discussion
- Topic: LTSpice - Help?
- Replies: 3
- Views: 1446
Re: LTSpice - Help?
I can't help but would like to know the answer.
It may be available in the YAHOO LTSPICE Group.
It may be available in the YAHOO LTSPICE Group.
- Mon Feb 07, 2011 11:28 pm
- Forum: Technical Discussion
- Topic: Output Transformer causing "red plating."
- Replies: 10
- Views: 4828
Re: Output Transformer causing "red plating."
Are you determining the turns ratio by measuring the resistance of the windings, or by applying a signal to the secondary and measuring the resulting signal on the Primary? Most transformers will have a resistive imbalance due to the winding topology (outer layers have more resistance for the same n...
- Mon Feb 07, 2011 11:13 pm
- Forum: Trainwreck Discussion
- Topic: Russian TrainWreck - Expresso Lite(Liverpool), Soviet tubes
- Replies: 56
- Views: 18992
Re: Russian TrainWreck - Expresso Lite(Liverpool), Soviet tubes
That is indeed a nice clip.
Finished set with speaker installed (upside down since the leads are up that way).
I decided to do round-overs on all corners. I think it looks better this way.
Finished set with speaker installed (upside down since the leads are up that way).
I decided to do round-overs on all corners. I think it looks better this way.
- Fri Feb 04, 2011 11:17 pm
- Forum: Trainwreck Discussion
- Topic: Russian TrainWreck - Expresso Lite(Liverpool), Soviet tubes
- Replies: 56
- Views: 18992
Re: Russian TrainWreck - Expresso Lite(Liverpool), Soviet tubes
Unfortunately (or maybe Fortunately considering my condition) it's too wet and cold to go outside and work on the speaker cab. Here is my complete (to be) system. The speaker is supposed to be a 1970s Rola Celestion G12M, 25W, 8 Ohm. The markings are T1871 or T1S71, and JJ28 with what appear to be t...
- Fri Feb 04, 2011 2:11 pm
- Forum: Technical Discussion
- Topic: wima caps....where should i try them?
- Replies: 3
- Views: 1189
Re: wima caps....where should i try them?
the .003s are a tad small for most applications, however there are some circuits using .0022 coupling caps. Reduce the following grid resistor by a factor of 1.5 for the same response. The .047s can be used as coupling caps in most designs where .022s are used by cutting the following grid resistor ...
- Fri Feb 04, 2011 2:02 pm
- Forum: Technical Discussion
- Topic: red plate 6L6 tube - next steps?
- Replies: 10
- Views: 4554
Re: red plate 6L6 tube - next steps?
sounds like a bad connection at the tube socket. Moving wires can change the stress on socket pins causing them to shift which will cause the pint o wipe against the mating socket and clean it. Wiggling the tube wipes the pin against the mating socket cleaning it. I'd watch closely for it to occur a...
- Wed Feb 02, 2011 5:05 pm
- Forum: Garage Talk
- Topic: The Gimp in ICU (Chest Pain Center).
- Replies: 16
- Views: 5024
Re: The Gimp in ICU (Chest Pain Center).
A little bit of a warning to you guys. My Heart Attack was not preceded by the normal symptoms of chest pain in the center of my chest, arm pain, neck pain, shortness of breath, or the feeling of weight on my chest. Because of this I didn't think I was having any heat trouble. I had experienced a sh...
- Tue Feb 01, 2011 11:05 pm
- Forum: Garage Talk
- Topic: The Gimp in ICU (Chest Pain Center).
- Replies: 16
- Views: 5024
Re: The Gimp in ICU (Chest Pain Center).
Thanks all.
I ended up with a stent put in and am still a little weak and queezy but at least I'm home.
I'll post again later.
I ended up with a stent put in and am still a little weak and queezy but at least I'm home.
I'll post again later.
- Tue Feb 01, 2011 11:04 pm
- Forum: Garage Talk
- Topic: Wind Turbines
- Replies: 15
- Views: 4694
Re: Wind Turbines
Hey thanks. I'm home again. The generator I read about was similar to this one: http://www.otherpower.com/17page1.html Except it had the coils cast in epoxy to hold them rigidly in place. The Neodymium magnets were also cast in epoxy. This allowed the assembly to keep very small spacing between the ...
- Sat Jan 29, 2011 2:48 am
- Forum: Garage Talk
- Topic: New Puppy
- Replies: 20
- Views: 4411
Re: New Puppy
Cute puppies and kittens. Nice Cat too.
- Sat Jan 29, 2011 2:45 am
- Forum: Garage Talk
- Topic: Wind Turbines
- Replies: 15
- Views: 4694
Re: Wind Turbines
I think I have some links at home on a 600W unit that is completely DIY.
When I get home out of ICU (Chest Pain Center) I'll try to find it.
When I get home out of ICU (Chest Pain Center) I'll try to find it.