Monkeymatic Hammond Stout

General discussion area for tube amps.

Moderators: pompeiisneaks, Colossal

Tubelube
Posts: 24
Joined: Thu Jan 16, 2014 3:41 pm

Thank You Xtian

Post by Tubelube »

Thank you xtian for your valuable info. You are correct about the site you mentioned, it is full of valuable information. :D
User avatar
xtian
Posts: 7036
Joined: Mon Apr 19, 2010 8:15 pm
Location: Chico, CA
Contact:

Re: Monkeymatic Hammond Stout

Post by xtian »

Sure, it's obvious that you're new at this stuff. But that's not a problem in itself. I was new at this stuff a few years ago, and asked plenty of similar questions. But there's no short answer! You have to learn how to bias a power section. You have to learn about the various PIs. About power string design, etc., etc.

So, there is no step-by-step guide to converting a Hammond power amp into a usable guitar power amp. But all the info you need to learn is here. You just need to start at the top:

http://ampgarage.com/forum/viewtopic.php?t=9023
I build and repair tube amps. http://amps.monkeymatic.com
Tubelube
Posts: 24
Joined: Thu Jan 16, 2014 3:41 pm

Hammond AO-39 conversion to modified Vox AC-15 Lite

Post by Tubelube »

How about this design.

http://home.comcast.net/~seluckey/amps/ ... d_ao39.pdf

I am thinking I could build the (Hammond AO-39 conversion to modified Vox AC-15 Lite) and instal the preamp jack input just before the volume control and after the tone control cap array in the schematic. In this case I could just not use the preamp part of this build unless I wanted to plug into the front end and use this as a guitar amp instead of a power amp. In the link I provided there is a conversions to build the (Hammond AO-39 conversion to MARSHALL 18 WATT Lite) also which I feel doesn't appear to be as viable for a power amp. What is your advice xtian? :?:
Tubelube
Posts: 24
Joined: Thu Jan 16, 2014 3:41 pm

Fun stuff!

Post by Tubelube »

I am working through the recommended following site at this time thanks for that! These are fun!
http://ampgarage.com/forum/viewtopic.php?t=9023
:D
User avatar
xtian
Posts: 7036
Joined: Mon Apr 19, 2010 8:15 pm
Location: Chico, CA
Contact:

Re: Monkeymatic Hammond Stout

Post by xtian »

Sure, that AC15 design is a good choice. The 2x EL84 power section is pretty standard, and as you say, you can plug a line-level input right where the volume control is, and use only the power section. Just make a passive FX loop at that point, and you're golden.

The 18-watt Lite amp's power section is basically the same:

http://mhuss.com/18watt/schematics/18wattLite2b.gif
I build and repair tube amps. http://amps.monkeymatic.com
sluckey
Posts: 3137
Joined: Sun Jul 22, 2007 7:48 pm
Location: Mobile, AL
Contact:

Re: Monkeymatic Hammond Stout

Post by sluckey »

off topic content removed
Last edited by sluckey on Tue Jan 20, 2015 1:41 am, edited 1 time in total.
User avatar
Structo
Posts: 15446
Joined: Wed Oct 17, 2007 1:01 am
Location: Oregon

Re: Monkeymatic Hammond Stout

Post by Structo »

@ Tubelube,

Please don't hijack other peoples threads for your amp problems.

Start a separate thread to address the problems you are experiencing.
Tom

Don't let that smoke out!
Post Reply