Tube build question
Moderators: pompeiisneaks, Colossal
-
- Posts: 4730
- Joined: Fri Jan 24, 2014 3:01 pm
- Location: 1/3rd the way out one of the arms of the Milkyway.
Tube build question
Ok, if the getter in a tube as only one connection point, then how the hell do they flash it before final seal up of the envelope?
When I die, I want to go like my Grandfather did, peacefully in his sleep.
Not screaming like the passengers in his car!
Cutting out a man's tongue does not mean he’s a liar, but it does show that you fear the truth he might speak about you!
Not screaming like the passengers in his car!
Cutting out a man's tongue does not mean he’s a liar, but it does show that you fear the truth he might speak about you!
Re: Tube build question
Big scary induction coil. Fascinating to watch. There are videos out there somewhere.
Re: Tube build question
Here's one.Firestorm wrote:Big scary induction coil. Fascinating to watch. There are videos out there somewhere.
http://www.youtube.com/watch?v=lOenKVTYyRQ
Re: Tube build question
That's one hell of a cool clip!
- VacuumVoodoo
- Posts: 924
- Joined: Fri Feb 17, 2006 6:27 pm
- Location: Goteborg, Sweden
- Contact:
Re: Tube build question
This is also a clear proof that cryo treatment is BS if not a scam.Zippy wrote:Here's one.Firestorm wrote:Big scary induction coil. Fascinating to watch. There are videos out there somewhere.
http://www.youtube.com/watch?v=lOenKVTYyRQ
Aleksander Niemand
------------------------
Life's a party but you get invited only once...
affiliation:TUBEWONDER AMPS
Zagray!-review
------------------------
Life's a party but you get invited only once...
affiliation:TUBEWONDER AMPS
Zagray!-review
Re: Tube build question
No, they've just been doing it in the wrong order all these years. You've to got to cryo treat the tube first, then flash the getter. Those that survive get sold for a premium.VacuumVoodoo wrote:This is also a clear proof that cryo treatment is BS if not a scam.
Re: Tube build question
I do all my tubes like these heat-fractured marbles.
[img1200]http://2.bp.blogspot.com/_ETkNFHOQl0E/T ... arbles.jpg[/img]
[img1200]http://2.bp.blogspot.com/_ETkNFHOQl0E/T ... arbles.jpg[/img]
I build and repair tube amps. http://amps.monkeymatic.com
Re: Tube build question
Id like to hang out with this guy. http://www.youtube.com/watch?v=L41ej3vHQT8 Not sure about the blouse though.
Re: Tube build question
This "Journey to the Center of a Tube" might help:
http://youtu.be/WnZRJjmOZb8
http://youtu.be/WnZRJjmOZb8
-
- Posts: 8
- Joined: Mon May 26, 2014 11:11 pm
Re: Tube build question
Ok first off hello I'm new here, second I need a little help I have autism and its hard for me to understand schematics(had a few problems on another forum so I gtta throw that out there) I have a univox 1221 I want to mod it, I'm not a Newbie I've modded smaller amps before, my problem is as far as I can tell I'm the only person who's ever tried this with this amp, I like a high gain so I want to put a master volume in for sure, post or pre phase opinions? And somebody that can tell me how to wire it up, and id like to be able to make the 2 channels footswitchable if that's possible, and any other mods that could make this amp a monster throw them out there, I just need to know how and where to wire or change the circuit around, thanks in advance and my personal email is onestepaway06@hotmail.com
Re: Tube build question
Welcome onestepaway.
You'll get better response if you start a dedicated thread rather than adding onto some other topic.
Good luck.
You'll get better response if you start a dedicated thread rather than adding onto some other topic.
Good luck.