reverb tank + sss filters + build

Overdrive Special, Steel String Singer, Dumbleland, Odyssey, Winterland, etc. -
Members Only

Moderators: pompeiisneaks, Colossal

Smokebreak
Posts: 1391
Joined: Tue Dec 18, 2012 5:53 pm
Location: Texas

Re: reverb tank + sss filters + build

Post by Smokebreak »

Rockwell666 wrote:wow what a beautiful build!
What value of trim pot did you use for the bottom of the CF? lastly are the 220K resistors off v7's plates tied to the grids? its hard to tell in the drawn schematic.
Im using a different circuit for the LTPI and CF and I want to try this setup out.
Sorry, just seeing this. I used mhartman's layout and tweaked from there, not the hand drawn scheme. But the 220Ks come off the cathode of the driver tube, and are fed with the bias voltage. 25K for the trimmer, and that is for the plates of the LTPI, not the CF ;)

For what it's worth, the owner just called and said the amp(1yr old) was whistling and whining when turned up. I had him replace the driver tube and that did the trick, and gave him more volume and headroom apparently. Just a reminder that a poor 12ax7 takes a beating in that position.
Krinkle
Posts: 192
Joined: Sun Dec 09, 2007 4:51 pm
Location: Pickering, Ontario

Re: reverb tank + sss filters + build

Post by Krinkle »

Smokebreak wrote: Sat Aug 22, 2015 7:14 pm I did the low filter, and realized that I was 1 lug position off on the whole thing for the high filter :evil: So I'll need to do that one again.
Here's the low filter. I omitted the 39K.
I think I'm building something between a JM an a #002. I schematicized mhartman's layout(nice work!!) and it's very similar to what I drew out, so I'll lean on that layout for sure. I've got about 12 pieces of paper in front of me, so that should get me something good !
Does anybody know what the part number is for this switch? The alpha switch I bought based on a part number floating around here doesn't have the extra solder tabs to mount the other side of the caps, they are cut off. I know this is 6 position but I can figure out how to buy the 7 position one if I have the part number for this one.
You do not have the required permissions to view the files attached to this post.
User avatar
Colossal
Posts: 5078
Joined: Sat Oct 20, 2007 9:04 pm
Location: Moving through Kashmir

Re: reverb tank + sss filters + build

Post by Colossal »

Looks killer! What a beast. I have Twin Iron (scratches beard)...
User avatar
dorrisant
Posts: 2689
Joined: Tue Sep 21, 2010 1:27 pm
Location: Somewhere between a river and a cornfield
Contact:

Re: reverb tank + sss filters + build

Post by dorrisant »

Krinkle wrote: Sun May 07, 2017 11:46 pm
Does anybody know what the part number is for this switch? The alpha switch I bought based on a part number floating around here doesn't have the extra solder tabs to mount the other side of the caps, they are cut off. I know this is 6 position but I can figure out how to buy the 7 position one if I have the part number for this one.

http://www.mouser.com/Search/ProductDet ... R2511F-17S
"Education is what you're left with after you have forgotten what you have learned" - Enzo
Krinkle
Posts: 192
Joined: Sun Dec 09, 2007 4:51 pm
Location: Pickering, Ontario

Re: reverb tank + sss filters + build

Post by Krinkle »

Thanks for the reply but that's the one I bought. I had any extra pins cut off.
User avatar
dorrisant
Posts: 2689
Joined: Tue Sep 21, 2010 1:27 pm
Location: Somewhere between a river and a cornfield
Contact:

Re: reverb tank + sss filters + build

Post by dorrisant »

Manufacturer PN is

SR2511F-0107-19R0B-E9-S-W-159.

From page one of the datasheet:
SR=Rotory
25=Diameter (1")
1=Number of Sections (Layers or Wafers)
1=Wiring Type Terminals
01=Number of Poles
07=Number of Positions
Blah, blah, blah...

So it should be wire terminals. :shock:
You do not have the required permissions to view the files attached to this post.
"Education is what you're left with after you have forgotten what you have learned" - Enzo
Krinkle
Posts: 192
Joined: Sun Dec 09, 2007 4:51 pm
Location: Pickering, Ontario

Re: reverb tank + sss filters + build

Post by Krinkle »

Sorry, I'm probably not being clear about what I'm asking. I have the same switch in your pic.

But take a look at the pic I posted. See how your switch has only 8 terminals, the one in the pic I posted has extra terminals, the other side (common side) of the caps are each connected to these extra terminals on the opposite side of the switch and it makes it easier and neater to wire/solder the caps onto the switch.
User avatar
dorrisant
Posts: 2689
Joined: Tue Sep 21, 2010 1:27 pm
Location: Somewhere between a river and a cornfield
Contact:

Re: reverb tank + sss filters + build

Post by dorrisant »

I see... No problem. Different strokes for different folks.

Here's what I did with lemons... I think it will work. :wink:
You do not have the required permissions to view the files attached to this post.
"Education is what you're left with after you have forgotten what you have learned" - Enzo
Bombacaototal
Posts: 1701
Joined: Thu Oct 06, 2016 5:53 am

Re: reverb tank + sss filters + build

Post by Bombacaototal »

This is what Hartman used on his SSS mentioned in this thread http://ampgarage.com/forum/viewtopic.ph ... n&start=45

The filters:
http://www.mouser.co.uk/Search/m_Produc ... R2921F-17S

I think is the same 7 pole filter you have but with 2 layers instead of 1, although it should make no difference. Maybe you should follow Hartman's wiring diagram from the layout?
Aaron
Posts: 642
Joined: Wed Feb 08, 2006 1:07 pm

Re: reverb tank + sss filters + build

Post by Aaron »

There's always the 2 layer option.
Aaron
You do not have the required permissions to view the files attached to this post.
Krinkle
Posts: 192
Joined: Sun Dec 09, 2007 4:51 pm
Location: Pickering, Ontario

Re: reverb tank + sss filters + build

Post by Krinkle »

Aaron wrote: Tue May 09, 2017 9:58 am There's always the 2 layer option.
Aaron
That looks like a good option, thanks.
User avatar
dorrisant
Posts: 2689
Joined: Tue Sep 21, 2010 1:27 pm
Location: Somewhere between a river and a cornfield
Contact:

Re: reverb tank + sss filters + build

Post by dorrisant »

Bombacaototal wrote: Tue May 09, 2017 6:24 am The filters:
http://www.mouser.co.uk/Search/m_Produc ... R2921F-17S
Minimum order = 1000 though. I'm not planning on building that many.
"Education is what you're left with after you have forgotten what you have learned" - Enzo
Krinkle
Posts: 192
Joined: Sun Dec 09, 2007 4:51 pm
Location: Pickering, Ontario

Re: reverb tank + sss filters + build

Post by Krinkle »

Ha ha, me neither! I guess I'll be doing it your way!
Post Reply